This is a draw knife from Flexcut co ltd (USA). Blade length 150 mm. I bought it for making a spoon.

3 types of hook knives. At the top is Morakniv's co ltd (Sweden) single-edged R. The bottom two ‡Tmade from concrete nails.

Rapid ratchet wrenches 13 and 14 from Fujikin co ltd, which is famous for valves. It's made of chrome vanadium steel, and it can be turned quickly and has a small ratchet pitch, so it's a pleasure to turn like a luxury wristwatch.

Marking ruler 600mm by Woodpeckers co ltd. It is an excellent one that can mark 4 places at the same time from the edge.

Small Nanjing plane 15mm. I bought it to carve out the handle of a spoon, and the blade uses Aogami No. 2.

Four-way curve plane 20 mm. I bought it to fix the seating surface of the chair.

his is the cutter which shaves a circle stick.1",3/4",1/2#.

The woodcarving CP-file. "CP" is the abbreviation of Chemical Polishing.

The adjustable fence made by OTORO. The length is 36inches.

The square set.68mm,95mm,120mm,174mm.

The wood clamp. The length is 8inches.

The Wixey Digital Height Gauge with Fractions.

Handy type Diamond whetstone. Red is #600,Blue is #1200.

Digital protractor 300mm.

The sculpture sword.The material is the Aogami in Japan.It is 470 dollars at 15.

Diamond whetstone. It is #6000 and #10000 in the both sides.It is 260 dollars.

The drill guide made by Kanzawa Tekko Co Ltd.130mm stroke. 10mm chuck.

Fosner bit.15 set.

The 2way sander made by Kanzawa Tekko Co.,Ltd. This is convenient hand sander.However, it isn't producing already.I thinks that it is regrettable.

The corner clamp made by NBK Co.,Ltd. The photograph above is the vise to install in the Workbench.I uses corner clamp when making the architrave.

The disk pad and sponge adapter. Pad is 50mm.Sponge is 75mm.

The 65 mm plane which is made by "Kawayoshi".This is cartridge blade and there is not necessity of grinding.

Drill. This stand was made from PVC and Japanese cedar.

Dial Gauge.The movement can be measured by the 1/100 mm unit. I picked up the gage at the waste article garbage dump and I made base stand.It have the powerful magnet.

The bench-vice to come across well in Tool-shop in Japan. I bought an exhibit at 1800 yen. The table can incline toward 45 degrees and 90 degrees.

This is craft145 made by OKADAIRON Co.Ltd. Since there is no side blade of hand-saw, blind pin can be cut without damaging the surface of a lower board.

The X-PIT model No.1 which is made by the Kanzawa ironworks.It's the possible drilling of ø16-40.I bought at the flea market.

I bought this at the flea market.It can be a perforator to ƒÓ120.The flexible drill.Made by KANZAWA.

It is the vise which recycled the jack of the car.The tighten up power is high.I made this, too.

The scale for the trimmer which I made.The way of doing its making is in the DIY gallery.

I am using a handsaw for bakum-saw and zet-saw mainly.zet-saw suits a live tree.

It is a hand vise, a hammer, a chisel, a hand planer. I want a chisel more.

reamer, hand nibble, chassis punch and then the set file from the left of the photograph. nibbler and a chassis wallop are made from HOZAN co.. It can be manufactured in 2 mm of aluminum.

It is vernier caliper. It is the necessary tool to manufacture a machine. 200 mm length, made by MITUTOYO.

The tool wagon which the wife picked up from the scrap iron garbage dump. It stores a tool. It is easy to use because it has a caster.

The tester bought 30 years before. It is made from SANWA Co.. 430-YTR. It often used at the amplifier construction at the time of the high school student.

I got this at the ironworks of the acquaintance. The width is 150 mm and can fix a work surely. Also, the protection plate of the magnet formula got together.

Do you know computation ruler? Before the present electronic calculator spread, it was in this and it was computing. I have maximum class of the qualification, but now I am not useful. Ricoh Co.. 1053-1